I'd like to welcome Dr. StrangeGun to the blogroll...
came across his site while looking for 1911 hammer hook pics.
(yeah, mine is POOCHED! Might be able to save it with some file time, though...)
Showing posts with label gunsmithing. Show all posts
Showing posts with label gunsmithing. Show all posts
29 July 2009
So.. looks like I get to play gunsmith...
Couple months back I bought a Colt Sistema, used (no, really?)...
Got to doing some research on 1911 issues- hammer follows, trigger stacking, safety work, etc...
Turns out the gun is a basket case. I'm looking at replacing the disconnector, sear, hammer, possibly the trigger, and safety.
Given that the gun is not stock (it's got a Kart National Match barrel) and was ripping chunks out of my hand, I might as well throw a beavertail in there while I'm at it...
Add to that some stripped out grip bushing holes...
... and then there's the issue that I'm not sure I prefer the curved backstap, though it does have a lanyard loop like I wanted...
I bought a couple hammers and safeties off gunbroker. I'm not convinced they're serviceable. They were sold as Colt takeouts- I am no expert, but cursory investigation leads me to believe they may well have been from some smith's "oh, shit!" bucket.. cast offs from a wayward slip of a file. Example-- I'm not sure the half-cock notches on the hammers are even there anymore.
I got a hammer from the local smith- it has a functional and serviceable halfcock (though it holds the hammer AWFULY close to the fully-decocked position- pics forthcoming) and fullcock. The halfcock IS held off the firing pin, so that's good.
Dropped in the takeout ambi-safety from my Taurus 1911AR. While it works, I would prefer something made from tool steel in that application. Also, being a righty, I prefer a non-ambi safety.
I've got it shootable now-- but it's by no means where I want it. Also, it's missing a lot of the finish. There's a Duracoat session in its near future. I'm debating between Flat Desert Earth or Dark Green for the frame, with a black slide. Need to scare up my airbrush and airbrush compressor first, though.
Scarey: When I took the ambi safeties out of the Taurus 1911, I installed the takeout safety, and had intended to carry the weapon. Luckily I didn't- because I found that the weapon would fire if I had the safety on-- *something* caused the safety to toggle off, and hammer to follow.
Got to researching this evening and discovered that, in dryfire, luckily. I was reading a thread on THR regarding safety fitment, and learned much!
Got to doing some research on 1911 issues- hammer follows, trigger stacking, safety work, etc...
Turns out the gun is a basket case. I'm looking at replacing the disconnector, sear, hammer, possibly the trigger, and safety.
Given that the gun is not stock (it's got a Kart National Match barrel) and was ripping chunks out of my hand, I might as well throw a beavertail in there while I'm at it...
Add to that some stripped out grip bushing holes...
... and then there's the issue that I'm not sure I prefer the curved backstap, though it does have a lanyard loop like I wanted...
I bought a couple hammers and safeties off gunbroker. I'm not convinced they're serviceable. They were sold as Colt takeouts- I am no expert, but cursory investigation leads me to believe they may well have been from some smith's "oh, shit!" bucket.. cast offs from a wayward slip of a file. Example-- I'm not sure the half-cock notches on the hammers are even there anymore.
I got a hammer from the local smith- it has a functional and serviceable halfcock (though it holds the hammer AWFULY close to the fully-decocked position- pics forthcoming) and fullcock. The halfcock IS held off the firing pin, so that's good.
Dropped in the takeout ambi-safety from my Taurus 1911AR. While it works, I would prefer something made from tool steel in that application. Also, being a righty, I prefer a non-ambi safety.
I've got it shootable now-- but it's by no means where I want it. Also, it's missing a lot of the finish. There's a Duracoat session in its near future. I'm debating between Flat Desert Earth or Dark Green for the frame, with a black slide. Need to scare up my airbrush and airbrush compressor first, though.
Scarey: When I took the ambi safeties out of the Taurus 1911, I installed the takeout safety, and had intended to carry the weapon. Luckily I didn't- because I found that the weapon would fire if I had the safety on-- *something* caused the safety to toggle off, and hammer to follow.
Got to researching this evening and discovered that, in dryfire, luckily. I was reading a thread on THR regarding safety fitment, and learned much!
26 July 2009
Got a smokin' deal...
I've been muling over getting a Beretta 92FS (as I understand it, it's the civvie version of the M9 the military uses) for quite some time. The only thing that really had me hesitant was that I was originally trained on the 1911 platform and while I did have some time with the M9 in my military service, I never cared for the slide-mounted safety. By that time it was just counterintuitive to have to reach for the safety waaaaay up there.
I'd heard there were versions of the Beretta with frame-mount, but as I understood it they were early models, and weren't the recipients of better metallurgy in the locking block and slide. I was aware of the Taurus offering, and I am a fan of Taurus, having several of their pistols, but didn't want an M9-type of pistol to pay upwards of $500- if it came to that I was going to grab another 24/7, maybe the OSS version that Taurus makes-- I'm already equipped with holsters for them and am quite happy with the platform.
Stopped in at a pawnshop "just to look" after picking up my Sistema and an AR15 from them for a great price-- there was a Taurus PT92AF(d) with decent finish (though showing some holster wear) for $200. I pawed it for a while, asked i they would move on the price-- they said they couldn't till the boss got back. Figured I would come back the nect day and talk with him about it, jumped in my jeep and headed home. On the way, I got to thinking that $200 for a decocker-equipped Beretta 92 clone with frame-mounted safety and decocker was more than fair, so I went back and bought it. It came with one mag, that apparently gave trouble- it wouldn't reliably hold the slide back, and would not drop free. No worries-- mags are cheap.
Went to the range, sure enough, the mag fed fine but wouldn't reliably hold the slide open after the last round. Bought a Promag to address that- problem solved.
The next day I stopped in at the local surplus store and saw 10 Army-surplus M9 mags in their case. 1 old civilian Beretta mag from the first lot of pistols with the Euro mag release in the heel of the weapon, 2 Beretta M9 contract, and the balance being checkmate mags. Aware of the problems with the checkmates, I asked what he wanted for all of the mags. $70. Sold!
I got to experimenting and found if I changed the spring and follower in the heel-release and the Taurus mag, I ended up with two mags that both worked just fine. Odd, but it works for now- I can always swap in Wolf springs if there's issue. Of course the Beretta and M9 mags won't work in the Taurus without being held in place- the mag release catch is different- but that's easily addressed. A few minutes with my Dremel tool and they'll stay in place. However, the front of the Beretta and M9 mags is just a hair wider, causing it to catch on the Taurus release. A few passes with a stone to relieve the lower side of the catch solves that problem as well, and they work slicker than one would expect a "noncompatible" mag to work. While it's true that if one were to swap the mag release to a left-hander, I'd have to go about modifying the other side of each mag, and would probably have to replace the mag release-- I don't care. I'm 1) not left handed, and 2) not getting rid of the weapon.
So all told, I've got the ability to carry about 210 rounds of pistol ammo on me, should the need occur. I don't expect it ever should- and in fact pray it doesn't-But for the price, you can't beat it. Just a hair over $300 for a serviceable weapon that's proven in combat (the Taurus is carried by the military and police of Brazil as well as a few other nations, and has seen service in Iraq, though I have no way of knowing if this weapon has a history), and enough mags to carry over 4 boxes of ammo. Works!
Taurus haters- send it to /dev/null. The 92 series is a proven commodity, and in fact the Taurus surpasses the Beretta original in several areas- example: the locking block. Also, as I understand it they're built on the Beretta tooling in Brazil, much the same as my Sistema was built on Colt tooling in Argentina.
Look for a series of posts on the modifications that I had to make to the mags, complete with How-To pics, possibly this evening...
I'd heard there were versions of the Beretta with frame-mount, but as I understood it they were early models, and weren't the recipients of better metallurgy in the locking block and slide. I was aware of the Taurus offering, and I am a fan of Taurus, having several of their pistols, but didn't want an M9-type of pistol to pay upwards of $500- if it came to that I was going to grab another 24/7, maybe the OSS version that Taurus makes-- I'm already equipped with holsters for them and am quite happy with the platform.
Stopped in at a pawnshop "just to look" after picking up my Sistema and an AR15 from them for a great price-- there was a Taurus PT92AF(d) with decent finish (though showing some holster wear) for $200. I pawed it for a while, asked i they would move on the price-- they said they couldn't till the boss got back. Figured I would come back the nect day and talk with him about it, jumped in my jeep and headed home. On the way, I got to thinking that $200 for a decocker-equipped Beretta 92 clone with frame-mounted safety and decocker was more than fair, so I went back and bought it. It came with one mag, that apparently gave trouble- it wouldn't reliably hold the slide back, and would not drop free. No worries-- mags are cheap.
Went to the range, sure enough, the mag fed fine but wouldn't reliably hold the slide open after the last round. Bought a Promag to address that- problem solved.
The next day I stopped in at the local surplus store and saw 10 Army-surplus M9 mags in their case. 1 old civilian Beretta mag from the first lot of pistols with the Euro mag release in the heel of the weapon, 2 Beretta M9 contract, and the balance being checkmate mags. Aware of the problems with the checkmates, I asked what he wanted for all of the mags. $70. Sold!
I got to experimenting and found if I changed the spring and follower in the heel-release and the Taurus mag, I ended up with two mags that both worked just fine. Odd, but it works for now- I can always swap in Wolf springs if there's issue. Of course the Beretta and M9 mags won't work in the Taurus without being held in place- the mag release catch is different- but that's easily addressed. A few minutes with my Dremel tool and they'll stay in place. However, the front of the Beretta and M9 mags is just a hair wider, causing it to catch on the Taurus release. A few passes with a stone to relieve the lower side of the catch solves that problem as well, and they work slicker than one would expect a "noncompatible" mag to work. While it's true that if one were to swap the mag release to a left-hander, I'd have to go about modifying the other side of each mag, and would probably have to replace the mag release-- I don't care. I'm 1) not left handed, and 2) not getting rid of the weapon.
So all told, I've got the ability to carry about 210 rounds of pistol ammo on me, should the need occur. I don't expect it ever should- and in fact pray it doesn't-But for the price, you can't beat it. Just a hair over $300 for a serviceable weapon that's proven in combat (the Taurus is carried by the military and police of Brazil as well as a few other nations, and has seen service in Iraq, though I have no way of knowing if this weapon has a history), and enough mags to carry over 4 boxes of ammo. Works!
Taurus haters- send it to /dev/null. The 92 series is a proven commodity, and in fact the Taurus surpasses the Beretta original in several areas- example: the locking block. Also, as I understand it they're built on the Beretta tooling in Brazil, much the same as my Sistema was built on Colt tooling in Argentina.
Look for a series of posts on the modifications that I had to make to the mags, complete with How-To pics, possibly this evening...
05 February 2009
Cavalry Arms Back in Production
A few months back, all of Cavarms' stock was seized by the BATFE goons for reasons not yet clear...
they've recently been allowed to go back into production, though they're not being given back the seized property as of yet.
They're pretty cheap, too. It's basically a Glock-ified AR15 lower receiver. Think I just found out where some of my tax refund is going...
they've recently been allowed to go back into production, though they're not being given back the seized property as of yet.
They're pretty cheap, too. It's basically a Glock-ified AR15 lower receiver. Think I just found out where some of my tax refund is going...
Subscribe to:
Posts (Atom)
Posts
